GORENJE Drying Machine Error Codes
GORENJE ERROR CODE BRIEF DESCRIPTION DETAILED DESCRIPTION FAULT INDICATION
F1 Temperature sensor connection open or short-circuit fault The fault is detected if the connection to the temperature sensor is open or if a short circuit occurs between the two sensor terminals. The washing program will be completed without heating. The fault will be displayed at the end of the washing program.
Check:
- Temperature sensor
- Electronic module
- Wiring harness. Display: F1.
F2 Door interlock connection open The fault is detected if the door interlock connection is open. The washing program will then be stopped. The fault will be displayed. The power supply of the door lock will be turned on. To turn on the washing program, the user must close the door (with the program activated). To continue the program (if a fault occurs during washing), the user must check if the door is closed, then press the "Start" button. If the fault occurs again, the washing program will stop. The power supply to the door lock will be disabled. If there is water in the machine, it is drained within 2 minutes. The fault will be displayed again, and it will not be possible to start the washing program.
Check:
- UBL
- Electronic module
- Wiring harness. Display: F2.
F3 The specified water level is not reached. The fault is detected if during water filling or heating phase, the water level does not reach level 1 during the filling time or 4 minutes of the heating phase. If the fault occurs the first time during the wash, the current program step will start again. If the malfunction occurs a second time (twice in a row), the program will be stopped and a malfunction will be displayed. To continue the program, the user must click on the Start button. If the fault occurs a third time, the washing program will be stopped, the fault will be displayed. You will not be able to start the washing program.
Check:
- Correct installation of drain hose
- Water tap
- Filling valve
- Blockage of nozzles
- Hydrostat
- Electronic module
- Wiring harness. Display: F3.
F4 The tacho connection is open or a short circuit has occurred. If the washing program is activated and the motor does not receive a signal from the tachometer, the first time it detects a malfunction for 1 minute. This is repeated 3 times. If during this time it is detected that the motor is operating OK, all previous faults are erased from the memory. If the fault is determined for the fourth time, the wash program will be stopped immediately. If the temperature is higher than 60 ° C, cooling with cold water is performed for 30 seconds. Then - drain the water for 2 minutes. The program stops. A fault is displayed.
Check:
- The engine and its components
- Electronic module
- Wiring harness. Display: F4.
F5 Motor short-circuit fault The fault is detected if the washing program is activated and the motor runs without monitoring the tee. The washing program will be stopped immediately. After 2 minutes - the second attempt. If the fault is not detected, the first detected fault is removed from the memory and the operation continues. If the same problem occurs again, the program will be completely stopped. If the temperature exceeds 60 ° C, cooling with cold water is performed for 30 seconds. Then - drain the water for 2 minutes. The program will be stopped. A fault is displayed.
Check:
- Electronic module
- Engine
- Wiring harness. Display: F5.
F6 The set temperature is not reached. The fault is detected if, after the heating phase, the temperature is more than 15 ° C lower than the set temperature. The wash program will be completed. The fault will be displayed at the end of the washing program.
Check:
- A heating element
- Temperature sensor
- Electronic module
- Wiring harness. Display: F6.
F7 The water level does not drop below level 1 The fault is detected if, after the drain phase, the water level still does not drop below level 1. If the fault occurred the first time during the wash program, the current step will be executed again. If the fault is detected a second time (twice consecutively), the washing program will be stopped and the fault will be displayed. To continue the washing program, the user must press the "Start" button. If the fault is detected a third time, the washing program will be stopped and the fault will be displayed, and the wash program will not start.
Check:
- Drain pump
- Nozzle of nozzles or drain hose
- Sewer obstruction Display: F8.
F8 MCA does not reach the maximum spin speed. The fault is detected if, at the end of the spin cycle of the test program, the spin speed is more than 150 rpm below the set speed. The fault will be displayed after the test program is completed.
Check:
- Belt condition
- Electronic module
- Engine
- Loading status of the tank with the laundry. Display: F8.
F9 Leakage: water in the machine. Aqua Stop has been activated The fault will be detected if the special Aqua Stop Sensor sensor signals a leak (the duration of the signal is at least 2 seconds). All valves will be turned off, the heater will also be turned off, and the main motor - stopped. After 3 seconds, a second check is carried out. If a fault is not found, the first fault will be deleted from the memory and the program will continue to run. If the fault is still present, the pump is switched on for 2 minutes and the water drained. A fault is displayed. You will not be able to start the washing program.
Check:
- Micro switch of akvastopa
- Leaks available. Display: F9.
F10 The water sensor does not work. The fault is detected if, at the beginning of each water filling program, the sensor does not work, the machine does not start filling with water. If the temperature is higher than 60 ° C, than cool with cold water for 30 seconds. If it accumulates water more than 2 minutes and STOP program. Display: F10.
F11 Overflow When overflow, the drain pump is activated. The drain works for 5 minutes, repeat after 2 minutes. The electronic module stops feeding tension to the flood valves, the washing program is reset. Display: F11.